View effective routes of a virtual hub: Azure Virtual WAN
Hi Guys, Most of Cisco document says below about 224.0.0.0/24 : "In general, addresses from 224.0.0.1 to 224.0.0.255 are reserved and used by various protocols (standard or proprietary, such as Hot Standby Router Protocol (HSRP)). Cisco recommends that you not use these for GDA in a multicast networ The "224.0.0.0" is a reserved range of IPv4 addresses having special multicast meaning (IPv4 Multicast). The command in itself just means that the multicast routing should go through the "eth0" interface. Destination Gateway Genmask Flags Metric Ref Use Iface 224.0.0.0 0.0.0.0 240.0.0.0 U 0 0 0 eth0 224.0.0.0 0.0.0.0 240.0.0.0 U 0 0 0 eth1 I recently read that route was deprecated/obsolete and that we should be using ip route instead, eg Local subnetwork Addresses in the range of 224.0.0.0 to 224.0.0.255 are individually assigned by IANA and designated for multicasting on the local subnetwork only. For example, the Routing Information Protocol (RIPv2) uses 224.0.0.9, Open Shortest Path First (OSPF) uses 224.0.0.5 and 224.0.0.6, and Multicast DNS uses 224.0.0.251. Figure A displays a routing table on a computer configured with an IP address of 100.100.1.75, a subnet mask of 255.0.0.0, and a default gateway of 100.100.1.250. Figure A: Each TCP/IP-based client maintains its own routing table. Feb 26, 2008 · This command is useful for routing table maintenance purposes. Use it to verify that the (S,G) mroute is installed in the mrouting table, or if it is not, why not. The key information in this output is the RPF interface. If there is an RPF check failure, the (S,G) mroute fails to install in the mrouting table.
The Routing Table - Router Alley
2016-9-15 · route delete 10.41.0.0 mask 255.255.0.0 例子9：要删除IP路由表中以10.开始的所有路由，执行以下命令： route delete 10.* 例子10：要将目标为10.41.0.0，子网掩码为255.255.0.0的路由的下一个跃点地址由10.27.0.1更改为10.27.0.25，执行以下命令：
The "224.0.0.0" is a reserved range of IPv4 addresses having special multicast meaning (IPv4 Multicast). The command in itself just means that the multicast routing should go through the "eth0" interface.
2020-7-18 · Destination Gateway Genmask Flags Metric Ref Use Iface 224.0.0.0 0.0.0.0 240.0.0.0 U 0 0 0 eth0 224.0.0.0 0.0.0.0 240.0.0.0 U 0 0 0 eth1 I recently read that route was deprecated/obsolete and that we should be using ip route instead, eg . ip route add 224.0.0.0/4 dev eth0 ip route add 224.0.0.0… 计算机网络课后习题习题五_百度文库 2012-10-5 · A router has the following (CIDR) entries in its routing table: Address/mask 135.46.56.0/22 135.46.60.0/22 192.53.40.0/23 default Next hop Interface 0 Interface 1 Router 1 Router 2 For each of the following IP addresses, what does the router do if a packet with that Network Administration: Displaying the Routing Table - …